Bourgault Indus., Ltd. v. United States , 2020 CIT 143 ( 2020 )

Slip Op. 20–143
UNITED STATES COURT OF INTERNATIONAL TRADE
____________________________________
:
BOURGAULT INDUSTRIES, LTD., :
:
Plaintiff, :
: Before: Richard K. Eaton, Judge
v. :
: Court No. 19-00111
UNITED STATES, :
:
Defendant. :
____________________________________ :
OPINION
[United States Department of Commerce’s final scope ruling sustained.]
Dated: October 13, 2020
George W. Thompson, Thompson & Associates, PLLC, of Washington, DC, argued for
Plaintiff.
Kelly A. Krystyniak, Trial Counsel, Commercial Litigation Branch, Civil Division, U.S.
Department of Justice, of Washington, DC, argued for Defendant. With her on the brief were
Joseph H. Hunt, Assistant Attorney General, Jeanne E. Davidson, Director, and L. Misha Preheim,
Assistant Director. Of Counsel on the brief was James Henry Ahrens II, Office of the Chief
Counsel for Trade Enforcement & Compliance, U.S. Department of Commerce, of Washington,
DC.
Eaton, Judge: This case involves a challenge to the United States Department of
Commerce’s (“Commerce” or the “Department”) ruling that the coulter disc hubs imported by
Bourgault Industries, Ltd. (“Bourgault” or “Plaintiff”) are “tapered roller housings” within the
scope of the antidumping duty order on tapered roller bearings from the People’s Republic of
China (“Order”).1 See Antidumping Duty Order on Tapered Roller Bearings and Parts Thereof,
1
See Tapered Roller Bearings and Parts Thereof, Finished or Unfinished, From the
People’s Rep. of China, 52 Fed. Reg. 22,667 (Dep’t Commerce June 15, 1987) (original final
antidumping duty order) amended by Tapered Roller Bearings From the People’s Rep. of China,
Court No. 19-00111 Page 2
Finished and Unfinished, from the People’s Rep. of China: Final Scope Ruling on Bourgault
Industries Ltd.’s Coulter Disc Hubs (June 3, 2019), P.R. 18 (“Final Scope Ruling”).
Bourgault, a U.S. manufacturer of agricultural equipment, imports coulter disc hubs to
make plows. A coulter disc hub “consists of a specialty casted [sic] flange, a specialty designed
indexed stub-axle, generic [tapered roller bearings], a crown nut, and a flattened end-cap.” Letter
from Junker & Nakachi to Sec’y Wilbur Ross (Feb. 19, 2019), P.R. 1 (“Scope Ruling Request”)
at 2 (emphasis added). Together with a blade, called a coulter disc, the hub is incorporated into an
“opener” assembly that is mounted to a plow. The coulter disc is mounted ahead and somewhat
above the plow blades. It cuts on an even edge to the furrow, and buries organic material (such as
the remains of cut corn stalks) to aid in their decomposition. The hub facilitates the functioning of
the disc by resisting the twisting and lateral forces caused when the disc encounters rocks, roots,
and other material as it is pulled through the earth. See Scope Ruling Request at 3.
The tapered roller bearings inside the coulter disc hub are highly compressed, i.e., they are
tightened with what Plaintiff calls “excess preload.”2 See Final Scope Ruling at 2. Because of this
preload, “coulter disc hubs turn only when sufficient lateral and twisting forces are applied against
the coulter blade when engaged with soil.” Scope Ruling Request at 4.
Bourgault disputes Commerce’s finding that its coulter disc hubs are within the scope of
the Order. It argues that (1) prior agency determinations interpreting the Order have identified
friction reduction as an “essential function” of in-scope merchandise; and that (2) substantial
record evidence shows that its preloaded tapered roller bearings inside the coulter disc hub prevent
55 Fed. Reg. 6669 (Dep’t Commerce Feb. 26, 1990) (correcting errors in calculated dumping
margins).
2
As shall be seen, “excess preload” has had two meanings in this proceeding.
Court No. 19-00111 Page 3
the hub from reducing friction; rather, the load increases friction. That is, the hub’s design ensures
that the coulter disc does not rotate, unless it is acted upon by sufficient force. See Pl.’s Mem.
Supp. Mot. J. Admin. R., ECF No. 14 (“Pl.’s Br.”); Pl.’s Reply, ECF No. 18. In this way, Plaintiff
claims, its coulter disc hubs are different from the “wheel hub units” that Commerce has found to
be within the scope of the Order, in previous scope rulings. See Pl.’s Br. 20. Plaintiff further argues
that if there were any question about the functionality of the coulter disc hubs, Commerce should
have commenced a scope inquiry. See Pl.’s Br. 27; 19 C.F.R. § 351.225(e), (k)(2) (2019). Plaintiff
thus asks the court to remand the Final Scope Ruling to Commerce “for reconsideration and
redetermination.” Pl.’s Br. 28.
Defendant the United States (“Defendant”), on behalf of Commerce, argues that, like in-
scope wheel hub units, coulter disc hubs are “tapered roller housings” (1) under the plain meaning
of the Order, and (2) because when sufficient pressure is applied, they do reduce friction. See
Def.’s Mem. Opp’n Pl.’s Mot. J. Admin. R., ECF No. 16 (“Def.’s Br.”). Defendant urges the court
to sustain the Final Scope Ruling as supported by substantial evidence and in accordance with law.
Jurisdiction is found under 28 U.S.C. § 1581(c) (2012) and 19 U.S.C. § 1516a(a)(2)(B)(vi)
(2012). The Final Scope Ruling is sustained.
BACKGROUND
I. The Order
The cornerstone in a scope determination is the language of the order itself. Walgreen Co.
v. United States, 620 F.3d 1350, 1357 (Fed. Cir. 2010) (citation omitted). On June 15, 1987,
Commerce issued the subject Order, which covered:
tapered roller bearings and parts thereof . . . ; flange, take up cartridge, and hanger
units incorporating tapered roller bearings . . . ; and tapered roller housings (except
Court No. 19-00111 Page 4
pillow blocks) incorporating tapered rollers, with or without spindles, whether or
not [for] automotive use . . . .
Order, 52 Fed. Reg. at 22,667 (references to Tariff Schedules of the United States omitted). The
Order does not mention functionality or use, except to say that it covered products “whether or
not” they were for “automotive use.” For more than thirty years, the Order’s language has remained
the same, except for updated references to the tariff schedule. See Tapered Roller Bearings and
Parts Thereof, Finished and Unfinished, From the People’s Rep. of China, 84 Fed. Reg. 6132(Dep’t Commerce Feb. 26, 2019) (final results of thirtieth admin. rev.) (citing the Order). Over the
years, however, Commerce has had occasion to review the scope of the Order, by way of “scope
rulings,” which are provided for in its regulations.
II. Regulatory Background on Scope Rulings
In a scope determination, “Commerce must first examine the language of the final order.”
Mid Continent Nail Corp. v. United States, 725 F.3d 1295, 1302 (Fed. Cir. 2013) (citations
omitted). If the language is clear, the plain meaning of the order controls. If the order is ambiguous,
the Department may issue scope rulings “that clarify the scope of an order . . . with respect to
particular products.” 19 C.F.R. § 351.225(a). The regulations set out rules regarding scope rulings,
including standards used in determining whether a product is within the scope of an order. Id.Whether an order is ambiguous is a question of law. See Meridian Prods., LLC v. United States,
851 F.3d 1375, 1382 (Fed. Cir. 2017).
“[I]n considering whether a particular product is included within the scope of an order . . . ,
[Commerce] will take into account . . . [t]he descriptions of the merchandise contained in the
petition, the initial investigation, and the determinations of [Commerce] (including prior scope
Court No. 19-00111 Page 5
determinations) and the [U.S. International Trade] Commission.” 19 C.F.R. § 351.225(k)(1).3 If
the sources listed in § 351.225(k)(1) are dispositive, Commerce will look no further.
If the (k)(1) sources are not dispositive, Commerce may commence a formal scope inquiry,
in which it will consider additional factors, listed in § 351.225(k)(2): (1) the physical
characteristics of the product, (2) the expectations of the ultimate purchasers, (3) the ultimate use
of the product, (4) the channels of trade in which the product is sold, and (5) the manner in which
the product is advertised and displayed. 19 C.F.R. § 351.225(k)(2), (e).
III. The Petition
On August 25, 1986, The Timken Company (“Timken”)4 filed a petition, on behalf of the
U.S. tapered roller bearing industry, alleging that imports of tapered roller bearings from China
were being, or were likely to be, sold at less than fair value in the United States, and were causing,
or threatened to cause, material injury to the U.S. industry. The petition stated that it covered “the
full range of [tapered roller bearings]”:
The scope of the petition includes the full range of TRBs[5], including single-
row bearings made with various angles and roller lengths and multiple-row
bearing assemblies. These bearings are available in two-row and four-row
assemblies and used where greater bearing rating is needed. Thrust bearings and
self-contained bearing packages (sometimes referred to as “unitized” bearings)
are also included.
3
The regulations set out different scope determination procedures for “products
completed or assembled” in the United States or foreign countries other than a country to which
an order applies, products with minor alterations, and later-developed products, none of which
apply here. See 19 C.F.R. § 351.225(g)-(j).
4
Timken is not a party to this lawsuit, but it participated in the scope ruling
proceeding before Commerce.
5
“TRBs” means tapered roller bearings.
Court No. 19-00111 Page 6
Letter from Stewart and Stewart to Sec’y Wilbur Ross (Mar. 25, 2019), P.R. 7-9 (“Timken
Opp’n”), Attach. 2 at 9 (excerpts from petition). Unlike the eventual Order itself, the petition
identified different purposes for which tapered roller bearings could be used, including agricultural
and industrial applications. See Timken Opp’n, Attach. 2.
Products identified in the petition included tapered roller bearings with different “settings,”
i.e., “a specific amount of play or preload.” Letter from Junker & Nakachi to Sec’y Wilbur Ross
(May 19, 2019), P.R. 15 (“Bourgault Rebuttal”), Ex. C at 2. For example, a Timken brochure
attached to the petition described, inter alia, two types of preloaded tapered roller bearings—the
“Hydra-Rib” and the “Spring-Rib”:
[The Hydra-Rib] is a self-contained tapered roller bearing that has a floating outer
race (or cup) rib which contacts the rollers. The floating rib is controlled by
hydraulic or pneumatic pressure in the sealed chamber behind the rib. Variable
pressure capabilities provide the unique capability of changing the preload in the
system to handle variable load or speed situations. This bearing is designed for
applications where bearing adjustment is critical over [a] wide range of speeds or
loads.
[The Spring-Rib] is a self-contained tapered roller bearing that has a floating outer
race (or cup) rib which contacts the rollers. The floating rib is controlled by springs.
This bearing is available in three grades of preload. They are light[,] medium and
heavy preload. The amount of preload is determined by the number of springs used
in the assembly. Use this bearing only where load and speed conditions are
relatively constant.
Timken Opp’n at 8-9 (quoting Timken brochure in Collective Ex. 3). In other words, Timken
sought investigation of tapered roller bearings with different grades of preload. As explained by a
Timken engineer in a declaration attached to the petition:
All tapered roller bearings use settings to optimize bearing performance which are
either specific amounts of axial end play or axial preload adjusted at assembly to
control the internal clearances between the rolling elements and the inner and outer
rings’ contacting races. . . . Preload is an axial interference or light compression
between rollers and races such that there is no measurable axial shaft movement
when a small force is applied. A preloaded [tapered roller bearing] has no internal
Court No. 19-00111 Page 7
clearance (measured either axially or radially) between the bearing’s rolling
elements and its inner and out[er] races.
Timken Opp’n, Attach. 4 ¶ 7 (emphasis added). Thus, preload is a common feature of tapered
roller bearings.
Bourgault notes that the petition addressed “excessive preload” in the context of how a
bearing’s setting impacts its useful life:
Some applications are set with preload to increase rigidity and positioning of highly
stressed parts that would otherwise be dramatically affected by excessive deflection
and misalignment.
Excessive preload must be avoided as bearing fatigue life can be drastically
reduced. Also, excessive preload can lead to lubrication problems and premature
bearing damage due to high operating temperature.
Bourgault Rebuttal, Ex. C at 2 (Timken’s Bearing Setting Techniques Manual) (emphasis added).
It is worth noting that the word excessive in this context is used in the sense of “too
much”—not in the sense of a “large amount.” That is, the Timken manual quoted by Bourgault
was warning that too much preload would cause the bearings to wear out.
IV. The Initial Investigation
In response to Timken’s petition, Commerce initiated a dumping investigation. See
Tapered Roller Bearings, Rollers and Parts Thereof, Finished or Unfinished, From the People’s
Rep. of China, 51 Fed. Reg. 33,283 (Dep’t Commerce Sept. 19, 1986) (notice of initiation). In its
preliminary determination, Commerce defined the scope of the investigation, which would later
be reflected in the Order:
tapered roller bearings and parts thereof . . . ; flange, take up cartridge, and hanger
units incorporating tapered roller bearings . . . ; and tapered roller housings (except
pillow blocks) incorporating tapered rollers, with or without spindles, whether or
not for automotive use . . . .
Court No. 19-00111 Page 8
Tapered Roller Bearings and Parts Thereof, Finished or Unfinished, From the People’s Rep. of
China, 52 Fed. Reg. 3833 (Dep’t Commerce Feb. 6, 1987) (preliminary determination of sales at
less than fair value) (references to Tariff Schedules of the United States omitted). The scope of the
investigation did not include an inquiry into preload, excessive or otherwise. Commerce made a
preliminary determination that dumping was occurring.
Following Commerce’s affirmative preliminary determination, the United States
International Trade Commission (“Commission”) commenced a material injury investigation. The
Commission applied Commerce’s scope definition.
In its report, the Commission pointed out some differences between ball bearings and
tapered roller bearings:
Tapered roller bearings are a part of the larger product category of antifriction
bearings. Antifriction bearings are machine components that permit free motion
between moving and fixed parts by holding or guiding the moving parts to minimize
friction and wear. In a bearing, a series of rollers or balls are usually mounted in a
separation or cage and enclosed between two rings called races. The rolling
elements are very important, since they transmit the physical load or force from the
moving parts to the stationary support. The two principal types of antifriction
bearings are ball bearings and roller bearings, depending on which type of rolling
elements [is] employed. Tapered roller bearings are preferred instead of ball
bearings for many applications because they are able to absorb both radial and
thrust loads, unlike ball bearings, which typically withstand only radial force.
Tapered Roller Bearings and Parts Thereof, and Certain Housings Incorporating Tapered Rollers
from Hungary, Italy, Japan, the People’s Rep. of China, Romania and Yugoslavia, Inv. Nos. 731-
TA-341-346, USITC Pub. 1899 (Oct. 1986) (Prelim.) (“ITC Investigation Preliminary
Determination”) at A-2 to A-3 & A-3 n.1 (emphasis added) (describing radial loads as “those
perpendicular to the axis rotation,” and thrust loads as “normally parallel to the level of rotation”).
As a result of its investigation, the Commission preliminarily determined that imports of the
subject merchandise were causing material injury to the U.S. industry.
Court No. 19-00111 Page 9
Commerce and the Commission confirmed their respective preliminary findings in their
final affirmative determinations. See Tapered Roller Bearings From the People’s Rep. of China,
52 Fed. Reg. 19,748 (Dep’t Commerce May 27, 1987) (final determination of sales at less than
fair value); see also Tapered Roller Bearings and Parts Thereof, and Certain Housings
Incorporating Tapered Rollers from Hungary, the People’s Rep. of China, and Romania, Inv. Nos.
731-TA-341, -344, -345, USITC Pub. 1983 (June 1987) (Final) (“ITC Investigation Final
Determination”).
V. Prior Scope Determinations
In the Final Scope Ruling, Commerce considered prior scope determinations under the
Order, and found that “Bourgault’s coulter disc hubs . . . are not substantially different from other
hub units Commerce has found to be in-scope merchandise.” Final Scope Ruling at 7. In particular,
Commerce cited several prior rulings on wheel hub units (also called wheel hub “assemblies”),
including a 2011 ruling requested by New Trend Engineering Ltd.6 See Mem. from Wendy J.
Frankel, Director, Office 8, Antidumping and Countervailing Duty Operations to Gary Taverman,
Acting Deputy Assistant Sec’y for Antidumping and Countervailing Duty Operations (Apr. 18,
2011) (“New Trend Scope Ruling”).
6
The New Trend Scope Ruling pertained to splined and non-splined wheel hub units
(assemblies) with and without antilock braking sensors. See Mem. from Wendy J. Frankel,
Director, Office 8, Antidumping and Countervailing Duty Operations to Gary Taverman, Acting
Deputy Assistant Sec’y for Antidumping and Countervailing Duty Operations (Apr. 18, 2011).
In addition to the New Trend Scope Ruling, Commerce cited other rulings on “hub units”
consisting of housed tapered roller bearings which it found to be covered by the Order. See Final
Scope Ruling at 7 (citing Tapered Roller Bearings from the People’s Rep. of China: Final Scope
Determination on Blackstone OTR’s Wheel Hub Assemblies (Feb. 7, 2011) and Tapered Roller
Bearings from the People’s Rep. of China: Final Scope Determination on Bosda’s Wheel Hub
Assemblies (June 14, 2011)).
Court No. 19-00111 Page 10
In the New Trend Scope Ruling, the merchandise at issue was wheel hub units with and
without antilock braking sensors. Commerce undertook an analysis of the § 351.225(k)(2) factors
with respect to wheel hub units with the sensors, and a § 351.225(k)(1) analysis of those without
the sensors. Ultimately, Commerce found that wheel hub units, both with and without antilock
braking sensors, were “tapered roller housings” because they had flanges that incorporated tapered
roller bearings. See New Trend Scope Ruling at 5, 10.
Additionally, in the New Trend Scope Ruling, after having considered the (k)(2) factors
with respect to wheel hub assemblies with antilock braking sensors, Commerce observed that the
wheel hub units’ “essential function” was “reducing friction.” Specifically, it stated that although
the wheel hubs had other features, those features, while adding functionality, “[did] not alter the
wheel hub assemblies’ essential function of reducing friction.” New Trend Scope Ruling at 11.
Because it reached this conclusion using a (k)(2) analysis, Commerce necessarily examined the
“ultimate use” factor. See New Trend Scope Ruling at 8; see also Mem. from Wendy J. Frankel,
Director, Office 8, Antidumping and Countervailing Duty Operations to Christian Marsh, Deputy
Assistant Sec’y for Antidumping and Countervailing Duty Operations (Dec. 8, 2010) at 10
(“Preliminary New Trend Scope Ruling”).
This Court sustained Commerce’s New Trend Scope Ruling as supported by substantial
evidence and in accordance with law in Power Train Components, Inc. v. United States, 37 CIT
781, 791, 911 F. Supp. 2d 1338, 1345, 1348 (2013). In its discussion, the Court recited
Commerce’s finding that the wheel hub assemblies’ additional features did not alter their “essential
function,” i.e., friction reduction. Id., 37 CIT at 785-86, 911 F. Supp. 2d at 1343-44. The Court
found no error with respect to that finding.
Court No. 19-00111 Page 11
Finally, in addition to its own prior scope rulings, Commerce took into account a
Commission report from the investigation that led to the Order. See Final Scope Ruling at 7 & n.44
(citing ITC Investigation Preliminary Determination); see also 19 C.F.R. § 351.225(k)(1)
(“[Commerce] will take into account . . . [t]he descriptions of the merchandise contained in . . . the
determinations of [Commerce] (including prior scope determinations) and the Commission.”).
Bourgault had cited the Commission report in its brief before the agency to support the argument
that the Order only covers tapered roller bearings whose primary purpose is the reduction of
friction—an argument that Commerce rejected because there was nothing in the Order that
supported it: “The scope language itself does not contemplate that [tapered roller bearings] must
be entirely free-turning; to the contrary, the documents in the underlying Petition (as supplemented
by a Timken engineer’s statement on this scope record) note that [tapered roller bearings] may
have different pre-load settings, depending upon their end-use.” See Final Scope Ruling at 8.7
7
In full text, Commerce stated:
[W]e disagree with Bourgault that the scope requires [tapered roller bearings] to
function solely to minimize friction and that only [tapered roller bearings] that
operate solely to minimize friction are covered by the Order. The scope language
itself does not contemplate that [tapered roller bearings] must be entirely free-
turning; to the contrary, the documents in the underlying Petition (as supplemented
by a Timken engineer’s statement on this scope record) note that [tapered roller
bearings] may have different pre-load settings, depending upon their end-use. In
this case, the [tapered roller bearings] are free-turning under the proper load, and,
like all [tapered roller bearings], they are optimized to resist lateral and shear forces
with even and minimal wear [of the bearings, the hub unit, and coulter disc].
Final Scope Ruling at 8.
Court No. 19-00111 Page 12
VI. The Subject Merchandise: Coulter Disc Hubs
As noted, Bourgault’s coulter disc hubs “consist[] of a specialty casted [sic] flange, a
specialty designed indexed stub-axle, generic [tapered roller bearings], a crown nut, and a flattened
end-cap.” Scope Ruling Request at 2. Together with a blade (a coulter disc), the hub is incorporated
into an “opener” assembly that is mounted to a plow. The disc cuts a crisp line on the furrow and
buries organic material. The hub facilitates the functioning of the disc by resisting the twisting and
lateral forces caused when the disc encounters rocks, roots, and other material as it is pulled
through the earth. When sufficient pressure is applied, however, supposedly by more immoveable
objects, the bearing permits the disc to rotate. See Scope Ruling Request at 3.
The tapered roller bearings in the coulter disc hub are highly compressed, i.e., according
to Plaintiff, they are tightened with “excess preload.” See Final Scope Ruling at 2. Because of this
preload, “coulter disc hubs turn only when sufficient lateral and twisting forces are applied against
the coulter blade when engaged with soil.” Scope Ruling Request at 4.
VII. The Final Scope Ruling Now Before the Court
On February 19, 2019, Bourgault filed its Scope Ruling Request, seeking a determination
by Commerce that its coulter disc hubs were outside the scope of the Order. In other words,
Bourgault maintained that its products were not:
tapered roller bearings and parts thereof . . . ; flange, take up cartridge, and hanger
units incorporating tapered roller bearings . . . ; and tapered roller housings (except
pillow blocks) incorporating tapered rollers, with or without spindles, whether or
not [for] automotive use . . . .
Order, 52 Fed. Reg. at 22,667.
In the Final Scope Ruling, Commerce considered the product’s description provided by
Bourgault in its Scope Ruling Request, i.e.:
Court No. 19-00111 Page 13
an indexed spindle (i.e., indexed stub-axle), cotter pin, triple lip seal, tapered roller
bearings, hub casting (i.e., casted [sic] flange), a second set of tapered roller
bearings, washer, crown nut, and a flattened end-cap.
Final Scope Ruling at 2. It concluded that the product was within the plain language of the Order:
We find that Bourgault’s imported coulter disc hubs meet the physical
characteristics of [tapered roller bearings] covered by the scope of the Order,
because they are tapered roller housings incorporating tapered rollers, including
a spindle. Further, there are no exclusions from the order for merchandise which is
subject to a different end use, and, in fact, the scope of the Order specifically covers
all [tapered roller bearings] and tapered roller housing (except pillow blocks),
“whether or not for automotive use.” Thus, we find that Bourgault’s coulter disc
hub units meet the plain language of the scope.
Final Scope Ruling at 6 (emphasis added). In other words, coulter disc hubs fell within the plain
meaning of the language of the Order because it was a “tapered roller housing.” Commerce
specifically found that the end use of the “tapered roller housing” was immaterial to the
determination of whether it was covered by the Order.
Commerce reached its determination after conducting a (k)(1) analysis. And although
Bourgault argues to the contrary, it is apparent that when reaching its conclusion, Commerce
considered the sources of information listed in 19 C.F.R. § 351.225(k)(1).8 See Final Scope Ruling
8
Subsection 351.225(k) provides:
[I]n considering whether a particular product is included within the scope of an
order . . . , [Commerce] will take into account the following:
(1) The descriptions of the merchandise contained in the petition, the initial
investigation, and the determinations of [Commerce] (including prior scope
determinations) and the Commission.
(2) When the above criteria are not dispositive, [Commerce] will further consider:
(i) The physical characteristics of the product;
(ii) The expectations of the ultimate purchasers;
(iii) The ultimate use of the product;
(iv) The channels of trade in which the product is sold; and
(v) The manner in which the product is advertised and displayed.
Court No. 19-00111 Page 14
at 6 (citing 19 C.F.R. § 351.225(k)(1)). For instance, Commerce cited its prior scope rulings, in
particular the New Trend Scope Ruling, regarding wheel hub units. It found that Bourgault’s
coulter disc hubs were like New Trend’s wheel hub units, in that they both housed tapered roller
bearings:
In [the New Trend Scope Ruling], Commerce found that hub units were covered by
the Order; this was upheld by the Court in Power Train Components. Similarly,
Commerce also found both automotive and non-automotive hub units, consisting
of housed [tapered roller bearings], to be covered by the Order in prior scope
rulings. Thus, we find that there is precedent in our prior consideration of various
tapered roller housings similar to Bourgault’s coulter disc hubs (also consisting of
[tapered roller bearings]) to support a finding that Bourgault’s coulter disc hubs are
within the scope of the Order.
Final Scope Ruling at 7 (first citing Power Train Components, 37 CIT at 787, 911 F. Supp. 2d at
1345; then citing Tapered Roller Bearings from the People’s Rep. of China: Final Scope
Determination on Blackstone OTR’s Wheel Hub Assemblies (Feb. 7, 2011) and Tapered Roller
Bearings from the People’s Rep. of China: Final Scope Determination on Bosda’s Wheel Hub
Assemblies (June 14, 2011)).
The Department acknowledged some differences between Bourgault’s coulter disc hubs
and the wheel hub units: “Unlike typical wheel hub assemblies, which principally function as anti-
friction devices, the purpose of the coulter disc hub is to resist the extreme twisting lateral forces,
and jarring impact forces, caused by plowing the soil in a spiral twisting fashion.” Final Scope
Ruling at 2. Commerce also recognized that the tapered roller bearings housed within Bourgault’s
coulter disc hubs “are tightened with excess preload,9 which reduces the ability of the hub to spin
freely.” Final Scope Ruling at 2 (emphasis added). It did not, however, find that the differences
19 C.F.R. § 351.225(k)(1)-(2).
9
Here, Commerce adopts Plaintiff’s use of “excess preload” as “a lot of preload,”
rather than “too much preload.”
Court No. 19-00111 Page 15
were material because this preload did not alter the fact that Bourgault’s coulter disc hubs
contained tapered roller bearings within the plain meaning of the Order.
Commerce also rejected Bourgault’s argument that its coulter disc hubs were not in-scope,
because their “essential function” was to reduce friction:
Bourgault attempts to differentiate its coulter disc hub units from automotive hub
units, citing to the Commission’s report and other scope rulings, which state that
the primary purpose of [tapered roller bearings] is to minimize friction and allow
for the free rotation of the hub unit. As an initial matter, we disagree that
Bourgault’s coulter disc hubs do not also fulfill these same criteria. Contrary to
Bourgault’s assertions, the [tapered roller bearings] in Bourgault’s coulter disc hubs
allow free rotation of the coulter disc, under the correct load, and they facilitate
even wear of the bearings, the hub unit, and coulter disc.
Final Scope Ruling at 7. Commerce found that “Bourgault’s coulter disc hub . . . allows the coulter
disc, which is attached to the plow frame, to turn freely through 360 degrees of motion, while
guiding the disc at the prescribed angle.” Final Scope Ruling at 7 n.44. It stated: “In this case, the
[tapered roller bearings] are free-turning under the proper load, and, like all [tapered roller
bearings], they are optimized to resist lateral and shear forces with even and minimal wear.” Final
Scope Ruling at 8. In other words, although sufficient force is required to overcome the “excess”
preload compressing the tapered roller bearings inside the coulter disc hub, the bearings permitted
the coulter disc to rotate.
Finding the language of the Order and the (k)(1) sources of information on the record
dispositive, Commerce did not consider the factors listed in § 351.225(k)(2). See Final Scope
Ruling at 6 (“We find that these sources are, together, dispositive as to whether the product at issue
is subject merchandise, in accordance with 19 CFR 351.225(k)(1). Therefore, we find it
unnecessary to consider the additional factors under 19 CFR 351.225(k)(2).”). This action
followed.
Court No. 19-00111 Page 16
STANDARD OF REVIEW
Commerce’s Final Scope Ruling will be upheld unless it is “unsupported by substantial
evidence on the record, or otherwise not in accordance with law.” 19 U.S.C. § 1516a(b)(1)(B)(i).
LEGAL FRAMEWORK
If the language of the Order clearly and unambiguously covers the subject merchandise,
the language controls. “The relevant scope terms are unambiguous if they have a single clearly
defined or stated meaning.” Meridian Prods., 851 F.3d at 1381 n.7 (citation omitted). “[T]he
question of whether the unambiguous terms of [the] scope [of an order] control the inquiry, or
whether some ambiguity exists, is a question of law” that the court reviews de novo. Id. at 1382.
If the order’s language is ambiguous, then Commerce “must turn to available [§ 351.225
(k)(1)] sources, including the petition, the initial investigation, and any earlier determinations by
Commerce and the [Commission].” Sunpreme Inc. v. United States, 946 F.3d 1300, 1309 (Fed.
Cir. 2020) (citations omitted); see also Atkore Steel Components, Inc. v. United States, 42 CIT __,
__, 313 F. Supp. 3d 1374, 1380 (2018) (citations omitted) (“If . . . the language of the scope order
is ambiguous, Commerce more fully analyzes the sources listed in § 351.225(k)(1). Where those
sources are dispositive, in other words, the history of the original investigation is clear, Commerce
will close the scope ruling proceedings with a ‘final scope ruling.’”).
Where § 351.225(k)(1) sources are not dispositive, Commerce commences a formal scope
inquiry. See 19 C.F.R. § 351.225(e). In that case, “Commerce must turn to available
[§ 351.225(k)(2)] sources, including the product’s physical characteristics, ultimate purchasers’
expectations, the product’s ultimate use, the channels of trade in which the product is sold, and the
Court No. 19-00111 Page 17
way the product is marketed.” Sunpreme, 946 F.3d at 1309 (citing Mid Continent, 725 F.3d at
1302; 19 C.F.R. § 351.225(k)(2)).
DISCUSSION
Plaintiff argues that the Final Scope Ruling is legally flawed because Commerce failed to
“take into account” prior agency determinations as required by its regulations. See 19 C.F.R.
§ 351.225(k)(1). In particular, Plaintiff claims that Commerce previously interpreted the Order to
include only merchandise that had as its “essential function” the reduction of friction, and that
Commerce failed to apply that “requirement” here. See Pl.’s Br. 24. For Plaintiff,
in-scope [tapered roller bearings] have been defined as products intended to reduce
friction from the outset of the antidumping duty investigation. That capability is the
sine qua non of the Order’s coverage. Merchandise that does not reduce friction
fails to meet that criterion and is excluded.
Pl.’s Br. 18. Plaintiff relies on excerpts from the New Trend Scope Ruling and Commission reports
to support its claims that in-scope tapered roller bearings’ “essential function” is reducing or
minimizing friction. See Pl.’s Br. 18-19 (citing New Trend Scope Ruling; ITC Investigation Final
Determination; Tapered Roller Bearings from China, Inv. No. 731-TA-344, USITC Pub. 4824
(Sept. 2018) (Fourth Rev.)).
For its part, Defendant maintains that Commerce correctly found that coulter disc hubs are
in-scope based on the plain meaning of the Order:
Commerce began its analysis with the language of the order, which includes
“tapered roller housings . . . [and] incorporating tapered rollers.” Commerce
explained that “Bourgault’s imported coulter disc hubs meet the physical
characteristics of [tapered roller bearings] covered by the scope of the order,
because they are tapered roller housings incorporating tapered rollers, including a
spindle.” Commerce further explained that “there are no exclusions from the
{order} for merchandise which is subject to a different end use, and, in fact, the
scope of the order specifically covers all [tapered roller bearings] and tapered roller
housing[s] (except pillow blocks), ‘whether or not for automotive use.’” Commerce
Court No. 19-00111 Page 18
thus determined that Bourgault’s coulter disc hubs units “meet the plain language
of the scope.”
Def.’s Br. 9-10 (internal citations omitted) (quoting Final Scope Ruling at 7-8).
In addition, Commerce found that coulter disc hubs did, in fact, reduce friction, “under the
correct load.” Final Scope Ruling at 7; see also Def.’s Br. 12 (“As Commerce explained, contrary
to its assertions, Bourgault’s coulter disc hubs do serve the purpose of reducing friction and
allowing free movement under the correct load, facilitating even wear of the bearings, the hub unit,
and coulter disc.”).
Moreover, Defendant maintains that Commerce satisfied the regulatory requirement to
“take into account” its prior rulings and those of the Commission, including the New Trend Scope
Ruling:
[In the New Trend Scope Ruling,] Commerce determined that New Trend’s wheel
hub units, which include “two non[-]removable tapered roller bearings in an inner
race and c[u]p that is machined into the unit’s flange, an outer [r]ace machined into
the assembly forging, and mounting studs for attachment of the assembly to an
automobile,” are “tapered roller housings” within the meaning of the order. . . .
Commerce reviewed that determination and found that “there is precedent in its
prior consideration of various tapered roller housing similar to Bourgault’s coulter
disc hubs (also consisting of [tapered roller bearings]) to support a finding that
Bourgault’s coulter disc hubs are within the scope of the Order.”
Def.’s Br. 10 (first quoting Power Train Components, 37 CIT at 783, 911 F. Supp. 2d at 1341-42;
then quoting Final Scope Ruling at 7).
The court is not persuaded by Plaintiff’s argument that Commerce committed legal or
factual error here. First, starting, as it must, with the language of the Order, Commerce found that
the subject coulter disc hubs fell within the plain meaning of the Order, i.e., as they are “tapered
roller housings.” Sunpreme, 946 F.3d at 1309. Plaintiff does not dispute that “a coulter disc hub’s
bearings are imported in a housing.” Pl.’s Br. 23. It insists, rather, that the Order’s language was
Court No. 19-00111 Page 19
not the “final word” on what it includes. For Bourgault, use of the (k)(1) factors demonstrates that
there is an exception in the Order for its bearings.
Specifically, Plaintiff maintains that Commerce violated its regulations by failing to
adequately consider prior agency rulings that, in Plaintiff’s view, established friction reduction as
a requirement of the Order. For example, Plaintiff relies on the New Trend Scope Ruling, which
pertained to wheel hub assemblies used in the front wheels of automobiles, both with and without
antilock braking sensors. All of the wheel hub assemblies subject to the scope request incorporated
two non-removable [tapered roller bearings] in an inner race and cup that are
machined into the unit’s flange, an outer race machined into the assembly forging,
wheel and brake “pilots” for aligning the wheels and brake rotors, and mounting
wheel studs. The majority of the assemblies consist of a flanged outer hub with two
[tapered roller bearings], into which has been pressed a flanged spindle having a
splined inner surface and mounting studs. The wheel hub assemblies are “sealed
for life,” “greased at factory,” and “the bearing preload is set at factory.” Certain of
the products do not have a splined spindle and certain of the products include
[antilock braking sensor] capability. New Trend’s wheel hub assemblies may be
categorized into the following types of merchandise: (1) splined without [antilock
braking sensor] elements; (2) non-splined without [antilock braking sensor]
elements; and (3) with [antilock braking sensor] elements.10
Preliminary New Trend Scope Ruling at 4.
Before Commerce, New Trend argued that its wheel hub assemblies were outside the scope
of the Order because of additional features and functions, e.g., flanges with wheel and brake pilots,
to align wheel and brake rotors, that went “beyond the antifriction and load bearing capabilities”
10
Commerce analyzed wheel hub assemblies without antilock braking sensors under
19 C.F.R. § 351.225(k)(1) because it found that (1) the plain language of the Order covered them:
“tapered roller housings . . . with or without spindles” (and whether or not the spindles had grooves,
i.e., were splined or non-splined); and (2) they were discussed in the ITC Investigation Final
Determination. See Preliminary New Trend Scope Ruling at 7-8. Although wheel hub assemblies
with antilock braking sensors were also “tapered roller housings,” they were not discussed in the
ITC Investigation Final Determination. Thus, Commerce found that it was less clear whether wheel
hub assemblies with antilock braking sensors were covered by the Order, and so conducted an
analysis of the factors in § 351.225(k)(2).
Court No. 19-00111 Page 20
of covered products. See Preliminary New Trend Scope Ruling at 7. Commerce disagreed with
that argument, and found that the additions were not sufficient to take the product outside the
Order.
In the New Trend case, Commerce found that the Order was ambiguous because there,
some of the subject hubs had the additional elements of an antilock braking system—a feature that
was not expressly covered by the Order. Importantly, this ambiguity had nothing to do with the
load of the tapered roller bearings that were part of the hub, excessive or otherwise.
Finding itself unable to resolve this ambiguity using the (k)(1) factors, Commerce went to
the (k)(2) factors. Among the factual findings Commerce made using these factors was that the
ultimate use of the bearings under review was to reduce friction. Thus, while the New Trend Scope
Ruling does observe that: “wheel hub units with additional features and functions retain the
essential function of wheel hub units covered by the Order; that is, they continue to reduce friction[,
and] thus, the additional features found on wheel hub units are engineering and design variations
. . . do not alter the fundamental nature of the subject [tapered roller bearing],” this observation is
in the context of the factual finding that the subject bearings did not differ from other bearings
covered by the Order. See Preliminary New Trend Scope Ruling at 7; see also New Trend Scope
Ruling at 11 (finding that added functionality did “not alter the wheel hub assemblies’ essential
function of reducing friction.”).
Here, because the “essential function” language was found in a scope determination using
the factor in (k)(2) based on the “ultimate use of the product,” the Department found the New
Trend Scope Ruling irrelevant to its (k)(1) examination. See Def.’s Br. 14 (internal citations
omitted) (“Bourgault omits that Commerce determined – and the Court sustained – that ‘wheel
hub assemblies with [antilock braking sensor] elements’ were within the scope of the order based
Court No. 19-00111 Page 21
on an analysis under the (k)(2) factors. Indeed, the language quoted by Bourgault comes from
Commerce’s analysis of the ‘ultimate use of the product.’”).
Although Bourgault cites New Trend as adding the requirement that, to be within the scope
of the Order, a tapered roller bearing must have the “essential function” of reducing friction, that
is not the case. For this kind of requirement to be added, the Order would have to be found to be
ambiguous. Ambiguity is a question of law. See Meridian Prods., 851 F.3d at 1382 (“[T]he
question of whether the unambiguous terms of [the] scope [of an order] control the inquiry, or
whether some ambiguity exists, is a question of law.”). While a scope ruling can resolve an
ambiguity, it cannot create one. Thus, the New Trend factual finding that two bearings are similar
because they reduce friction cannot serve to introduce an ambiguity into the language of the Order
as a matter of law.
As to the Commission’s report, the report does indeed describe tapered roller bearings as
being “a part of the larger product category of antifriction bearings.” See ITC Investigation
Preliminary Determination at A-2. It is included in order to draw a distinction between ball
bearings and tapered roller bearings on the basis of tapered roller bearings’ ability to “absorb both
radial and thrust loads.” See ITC Investigation Preliminary Determination at A-3. There is no
indication that this explanation of the differences in bearings was meant to limit the kinds of
tapered roller bearings included in the Order or to add a requirement that to be included in the
Order a bearing must have as its essential function the reduction of friction.
As noted, when interpreting the scope of an order, Commerce must start with the plain
language of the order itself. See Mid Continent, 725 F.3d at 1302. Commerce did not identify an
ambiguity in the Order, and there is little to convince the court that Commerce was wrong. Indeed,
although Commerce undertook a (k)(1) analysis, it is not clear that Commerce was required to do
Court No. 19-00111 Page 22
so because Bourgault has not shown the Order’s language to be ambiguous. Thus, the plain
language of the Order controls, and covers Plaintiff’s merchandise as “tapered roller housings.”
Moreover, even if it could be said that the reduction of friction is an essential function of a
tapered roller bearing for it to be found within the scope of the Order, the outcome would be the
same. Here, Plaintiff’s tapered roller bearings perform two tasks. First, because of their load, they
keep the coulter disc rigid and at the proper angle for turning the soil as it is dragged across a field.
Second, when sufficient force is applied (when, it can be assumed, the disc hits on an immovable
object) the pressure applied by the load is relieved and the bearings turn allowing rotation of the
coulter disc. See Def.’s Br. 12 (quoting Final Scope Ruling at 5) (“[E]ven though the coulter
[tapered roller bearings] do not allow for rotation as fast or reduce friction at the same level as
[tapered roller bearings] with different preload settings, they still allow rotation . . . .”); see also
Final Scope Ruling at 7 (“Contrary to Bourgault’s assertions, the [tapered roller bearings] in
Bourgault’s coulter disc hubs allow free rotation of the coulter disc, under the correct load, and
they facilitate even wear of the bearings, the hub unit, and coulter disc.”). Commerce reached these
conclusions as a matter of fact, and Bourgault does not dispute that fact. There being nothing
unreasonable about these conclusions, the court finds that substantial evidence supports
Commerce’s finding that coulter disc hubs reduce friction. See Sunpreme, 946 F.3d at 1308
(citations omitted) (“A decision is supported by substantial evidence if the evidence amounts to
more than a mere scintilla and a reasonable mind might accept it as adequate to support a
conclusion.”).
Finally, the court is not convinced that Commerce failed in its duty to “take into account”
the information required by its regulations. Subsection 351.225(k)(1) requires that “in considering
whether a particular product is included within the scope of an order . . . , [Commerce] will take
Court No. 19-00111 Page 23
into account . . . [t]he descriptions of the merchandise contained in the petition, the initial
investigation, and the determinations of [Commerce] (including prior scope determinations) and
the Commission.” Although it may have been unnecessary, it is apparent from the Final Scope
Ruling that Commerce met that standard. Indeed, it is clear that Commerce did take this
information into account, but reached different conclusions in doing so than Bourgault wished. See
Atkore, 313 F. Supp. 3d at 1380 (“If . . . the language of the scope order is ambiguous, Commerce
more fully analyzes the sources listed in § 351.225(k)(1).”).
CONCLUSION
For the reasons stated above, Plaintiff’s motion for judgment on the agency record is
denied, and the Final Scope Ruling is sustained. Judgment shall be entered accordingly.
/s/ Richard K. Eaton
Richard K. Eaton, Judge
Dated: October 13, 2020
New York, New York